Mevotech MB30325 Wheel Bearing and Hub Assembly - Rear
Rear Wheel Bearing Hub for Nissan Rogue
The Mevotech MB30325 is a rear wheel bearing and hub assembly engineered for 2008-2013 Nissan Rogue models. Built as a Gen 3 roll-form design, it is pre-greased and uses a non-integral ABS sensor layout for a direct replacement on the rear axle.
Key Features
- Fits 2008-2013 Nissan Rogue, rear
- Mevotech Supreme Parts application-specific design for durability-focused service
- Gen 3 roll-form construction
- Pre-greased assembly for ready-to-install service
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 5 bolt holes
- Inside diameter: 68 mm; outside diameter: 148 mm
Product Details
Mevotech MB30325 is a rear hub bearing assembly for the Nissan Rogue, covering 2008-2013 model years. The Supreme Parts line is engineered in-house with vehicle-specific upgrades for demanding passenger and commercial use, including SUVs, fleets, and working trucks. This assembly is built to replace the rear wheel bearing and hub unit with a pre-greased, roll-form design that supports consistent fitment and serviceability. This part cross-references Timken HA590241 and SKF BR930731 for the same application.
Common Issues This Part Can Address
- Rear wheel bearing noise or growling from the hub area
- Excessive wheel play or looseness at the rear wheel
- ABS warning concerns related to the hub sensor configuration
- Uneven rear wheel rotation caused by hub wear
- Service replacement for a worn rear hub assembly on a Nissan Rogue
Installation Notes
Confirm rear-position fitment before ordering: Fits 2008-2013 Nissan Rogue, rear. Verify the 5-bolt hub pattern, 4 flange bolt holes, 68 mm inside diameter, and 148 mm outside diameter against the original part. Because this assembly uses a non-integral ABS sensor layout, match the vehicle’s sensor arrangement during installation. The pre-greased design helps simplify setup, but proper torque procedures and clean mounting surfaces remain important for a correct repair.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering for durability-focused replacement service. MB30325 is designed for high-use vehicles and daily-driven applications where consistent hub performance matters.
Rear Wheel Bearing Hub for Nissan Rogue
The Mevotech MB30325 is a rear wheel bearing and hub assembly engineered for 2008-2013 Nissan Rogue models. Built as a Gen 3 roll-form design, it is pre-greased and uses a non-integral ABS sensor layout for a direct replacement on the rear axle.
Key Features
- Fits 2008-2013 Nissan Rogue, rear
- Mevotech Supreme Parts application-specific design for durability-focused service
- Gen 3 roll-form construction
- Pre-greased assembly for ready-to-install service
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 5 bolt holes
- Inside diameter: 68 mm; outside diameter: 148 mm
Product Details
Mevotech MB30325 is a rear hub bearing assembly for the Nissan Rogue, covering 2008-2013 model years. The Supreme Parts line is engineered in-house with vehicle-specific upgrades for demanding passenger and commercial use, including SUVs, fleets, and working trucks. This assembly is built to replace the rear wheel bearing and hub unit with a pre-greased, roll-form design that supports consistent fitment and serviceability. This part cross-references Timken HA590241 and SKF BR930731 for the same application.
Common Issues This Part Can Address
- Rear wheel bearing noise or growling from the hub area
- Excessive wheel play or looseness at the rear wheel
- ABS warning concerns related to the hub sensor configuration
- Uneven rear wheel rotation caused by hub wear
- Service replacement for a worn rear hub assembly on a Nissan Rogue
Installation Notes
Confirm rear-position fitment before ordering: Fits 2008-2013 Nissan Rogue, rear. Verify the 5-bolt hub pattern, 4 flange bolt holes, 68 mm inside diameter, and 148 mm outside diameter against the original part. Because this assembly uses a non-integral ABS sensor layout, match the vehicle’s sensor arrangement during installation. The pre-greased design helps simplify setup, but proper torque procedures and clean mounting surfaces remain important for a correct repair.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering for durability-focused replacement service. MB30325 is designed for high-use vehicles and daily-driven applications where consistent hub performance matters.
Description
Rear Wheel Bearing Hub for Nissan Rogue
The Mevotech MB30325 is a rear wheel bearing and hub assembly engineered for 2008-2013 Nissan Rogue models. Built as a Gen 3 roll-form design, it is pre-greased and uses a non-integral ABS sensor layout for a direct replacement on the rear axle.
Key Features
- Fits 2008-2013 Nissan Rogue, rear
- Mevotech Supreme Parts application-specific design for durability-focused service
- Gen 3 roll-form construction
- Pre-greased assembly for ready-to-install service
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 5 bolt holes
- Inside diameter: 68 mm; outside diameter: 148 mm
Product Details
Mevotech MB30325 is a rear hub bearing assembly for the Nissan Rogue, covering 2008-2013 model years. The Supreme Parts line is engineered in-house with vehicle-specific upgrades for demanding passenger and commercial use, including SUVs, fleets, and working trucks. This assembly is built to replace the rear wheel bearing and hub unit with a pre-greased, roll-form design that supports consistent fitment and serviceability. This part cross-references Timken HA590241 and SKF BR930731 for the same application.
Common Issues This Part Can Address
- Rear wheel bearing noise or growling from the hub area
- Excessive wheel play or looseness at the rear wheel
- ABS warning concerns related to the hub sensor configuration
- Uneven rear wheel rotation caused by hub wear
- Service replacement for a worn rear hub assembly on a Nissan Rogue
Installation Notes
Confirm rear-position fitment before ordering: Fits 2008-2013 Nissan Rogue, rear. Verify the 5-bolt hub pattern, 4 flange bolt holes, 68 mm inside diameter, and 148 mm outside diameter against the original part. Because this assembly uses a non-integral ABS sensor layout, match the vehicle’s sensor arrangement during installation. The pre-greased design helps simplify setup, but proper torque procedures and clean mounting surfaces remain important for a correct repair.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering for durability-focused replacement service. MB30325 is designed for high-use vehicles and daily-driven applications where consistent hub performance matters.
