Mevotech H512040 Wheel Bearing and Hub Assembly - Rear
Mevotech H512040 Rear Wheel Bearing Hub
Mevotech H512040 is a rear wheel bearing and hub assembly built for the 1995 Mitsubishi Expo. It features a Gen 3 roll-form design, a non-integral ABS sensor setup, and a pre-greased construction for service-ready installation. This Mevotech Supreme hub bearing assembly is engineered for high-use passenger and working vehicles, including the Mitsubishi Expo rear application.
Key Features
- Part number H512040 rear wheel bearing and hub assembly
- Fits 1995 Mitsubishi Expo, rear
- Gen 3 roll-form design for the hub assembly
- Non-integral ABS sensor configuration
- Pre-greased for installation readiness
- 4-bolt hole design
- 90 mm inside diameter and 140 mm outside diameter
Application Details
Built under Mevotech Supreme Parts engineering, H512040 is made with application-specific upgrades for durability and consistent performance in demanding use. The rear hub assembly is a direct replacement for the 1995 Mitsubishi Expo rear position and is also cross-referenced to Monroe Shocks & Struts (e.g., 172286, 182286) for the same application. If you are sourcing a Mitsubishi Expo rear wheel bearing hub assembly, H512040 provides the correct fitment and design details for that vehicle.
Common Problems This Part Addresses
- Rear wheel bearing noise or growling
- Excessive hub play or looseness
- Uneven wheel rotation caused by worn bearing surfaces
- ABS sensor configuration mismatch during replacement
- Service delays from a worn or damaged rear hub assembly
Installation Notes
Confirm rear-position fitment before ordering and verify the 4-bolt hole pattern, 90 mm inside diameter, and 140 mm outside diameter against the original part. Because this assembly is pre-greased, it arrives ready for installation, but proper torque procedures and a clean mounting surface are still important for a reliable repair. Use the vehicle service manual for the Mitsubishi Expo rear hub replacement process.
Quality Assurance
Mevotech Supreme hub bearing assemblies are engineered in-house with application-specific design updates for durability and performance in commercial and passenger vehicle service. H512040 is built for the demands of the Mitsubishi Expo rear application and follows Mevotech’s Supreme Parts construction standards.
Mevotech H512040 Rear Wheel Bearing Hub
Mevotech H512040 is a rear wheel bearing and hub assembly built for the 1995 Mitsubishi Expo. It features a Gen 3 roll-form design, a non-integral ABS sensor setup, and a pre-greased construction for service-ready installation. This Mevotech Supreme hub bearing assembly is engineered for high-use passenger and working vehicles, including the Mitsubishi Expo rear application.
Key Features
- Part number H512040 rear wheel bearing and hub assembly
- Fits 1995 Mitsubishi Expo, rear
- Gen 3 roll-form design for the hub assembly
- Non-integral ABS sensor configuration
- Pre-greased for installation readiness
- 4-bolt hole design
- 90 mm inside diameter and 140 mm outside diameter
Application Details
Built under Mevotech Supreme Parts engineering, H512040 is made with application-specific upgrades for durability and consistent performance in demanding use. The rear hub assembly is a direct replacement for the 1995 Mitsubishi Expo rear position and is also cross-referenced to Monroe Shocks & Struts (e.g., 172286, 182286) for the same application. If you are sourcing a Mitsubishi Expo rear wheel bearing hub assembly, H512040 provides the correct fitment and design details for that vehicle.
Common Problems This Part Addresses
- Rear wheel bearing noise or growling
- Excessive hub play or looseness
- Uneven wheel rotation caused by worn bearing surfaces
- ABS sensor configuration mismatch during replacement
- Service delays from a worn or damaged rear hub assembly
Installation Notes
Confirm rear-position fitment before ordering and verify the 4-bolt hole pattern, 90 mm inside diameter, and 140 mm outside diameter against the original part. Because this assembly is pre-greased, it arrives ready for installation, but proper torque procedures and a clean mounting surface are still important for a reliable repair. Use the vehicle service manual for the Mitsubishi Expo rear hub replacement process.
Quality Assurance
Mevotech Supreme hub bearing assemblies are engineered in-house with application-specific design updates for durability and performance in commercial and passenger vehicle service. H512040 is built for the demands of the Mitsubishi Expo rear application and follows Mevotech’s Supreme Parts construction standards.
Original: $76.58
-65%$76.58
$26.80Description
Mevotech H512040 Rear Wheel Bearing Hub
Mevotech H512040 is a rear wheel bearing and hub assembly built for the 1995 Mitsubishi Expo. It features a Gen 3 roll-form design, a non-integral ABS sensor setup, and a pre-greased construction for service-ready installation. This Mevotech Supreme hub bearing assembly is engineered for high-use passenger and working vehicles, including the Mitsubishi Expo rear application.
Key Features
- Part number H512040 rear wheel bearing and hub assembly
- Fits 1995 Mitsubishi Expo, rear
- Gen 3 roll-form design for the hub assembly
- Non-integral ABS sensor configuration
- Pre-greased for installation readiness
- 4-bolt hole design
- 90 mm inside diameter and 140 mm outside diameter
Application Details
Built under Mevotech Supreme Parts engineering, H512040 is made with application-specific upgrades for durability and consistent performance in demanding use. The rear hub assembly is a direct replacement for the 1995 Mitsubishi Expo rear position and is also cross-referenced to Monroe Shocks & Struts (e.g., 172286, 182286) for the same application. If you are sourcing a Mitsubishi Expo rear wheel bearing hub assembly, H512040 provides the correct fitment and design details for that vehicle.
Common Problems This Part Addresses
- Rear wheel bearing noise or growling
- Excessive hub play or looseness
- Uneven wheel rotation caused by worn bearing surfaces
- ABS sensor configuration mismatch during replacement
- Service delays from a worn or damaged rear hub assembly
Installation Notes
Confirm rear-position fitment before ordering and verify the 4-bolt hole pattern, 90 mm inside diameter, and 140 mm outside diameter against the original part. Because this assembly is pre-greased, it arrives ready for installation, but proper torque procedures and a clean mounting surface are still important for a reliable repair. Use the vehicle service manual for the Mitsubishi Expo rear hub replacement process.
Quality Assurance
Mevotech Supreme hub bearing assemblies are engineered in-house with application-specific design updates for durability and performance in commercial and passenger vehicle service. H512040 is built for the demands of the Mitsubishi Expo rear application and follows Mevotech’s Supreme Parts construction standards.
