Mevotech H513216 Wheel Bearing and Hub Assembly - Front
Mevotech H513216 Front Hub Assembly
The Mevotech H513216 is a front wheel bearing and hub assembly built for the 1993 Volvo 850. It combines a pre-greased Gen 3 design with a non-integral ABS sensor layout and a 4-bolt flange pattern for a direct driveline and axle service replacement.
Key Features
- Part number H513216 for front hub and bearing service
- Fits 1993 Volvo 850, front
- Gen 3 design for application-specific hub bearing replacement
- Pre-greased for ready-to-install service
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 4 bolt holes total
- Inside diameter: 68 mm
- Outside diameter: 135.5 mm
Product Details
Mevotech Supreme hub bearing assemblies are engineered in-house with upgrades tailored to the application. For the Volvo 850 front hub service, H513216 is built for passenger vehicle use and follows the dimensions and mounting layout needed for a proper replacement. The pre-greased construction and Gen 3 design support efficient service on high-use vehicles, including daily-driven cars and working fleets. This part cross-references SKF BR930245 for the same application.
Common Problems This Part Can Address
- Front wheel bearing noise or growling from the hub area
- Excessive wheel play or looseness at the front axle
- ABS-related service needs tied to a non-integral sensor setup
- Hub wear from repeated mileage and load cycles
- Front-end vibration caused by a worn bearing assembly
Installation Notes
Confirm the 4-bolt flange pattern, 68 mm inside diameter, and 135.5 mm outside diameter before installation. This assembly is pre-greased, which helps streamline service, but proper torque procedures and clean mounting surfaces are still important for a secure repair. Verify front-position application on the 1993 Volvo 850 before ordering or installing H513216.
Quality Assurance
Mevotech Supreme parts are engineered in-house with application-specific upgrades for durability and performance. H513216 is built as a service replacement for front hub bearing applications on the 1993 Volvo 850 and is backed by Mevotech’s product engineering standards.
Mevotech H513216 Front Hub Assembly
The Mevotech H513216 is a front wheel bearing and hub assembly built for the 1993 Volvo 850. It combines a pre-greased Gen 3 design with a non-integral ABS sensor layout and a 4-bolt flange pattern for a direct driveline and axle service replacement.
Key Features
- Part number H513216 for front hub and bearing service
- Fits 1993 Volvo 850, front
- Gen 3 design for application-specific hub bearing replacement
- Pre-greased for ready-to-install service
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 4 bolt holes total
- Inside diameter: 68 mm
- Outside diameter: 135.5 mm
Product Details
Mevotech Supreme hub bearing assemblies are engineered in-house with upgrades tailored to the application. For the Volvo 850 front hub service, H513216 is built for passenger vehicle use and follows the dimensions and mounting layout needed for a proper replacement. The pre-greased construction and Gen 3 design support efficient service on high-use vehicles, including daily-driven cars and working fleets. This part cross-references SKF BR930245 for the same application.
Common Problems This Part Can Address
- Front wheel bearing noise or growling from the hub area
- Excessive wheel play or looseness at the front axle
- ABS-related service needs tied to a non-integral sensor setup
- Hub wear from repeated mileage and load cycles
- Front-end vibration caused by a worn bearing assembly
Installation Notes
Confirm the 4-bolt flange pattern, 68 mm inside diameter, and 135.5 mm outside diameter before installation. This assembly is pre-greased, which helps streamline service, but proper torque procedures and clean mounting surfaces are still important for a secure repair. Verify front-position application on the 1993 Volvo 850 before ordering or installing H513216.
Quality Assurance
Mevotech Supreme parts are engineered in-house with application-specific upgrades for durability and performance. H513216 is built as a service replacement for front hub bearing applications on the 1993 Volvo 850 and is backed by Mevotech’s product engineering standards.
Original: $92.65
-65%$92.65
$32.43Description
Mevotech H513216 Front Hub Assembly
The Mevotech H513216 is a front wheel bearing and hub assembly built for the 1993 Volvo 850. It combines a pre-greased Gen 3 design with a non-integral ABS sensor layout and a 4-bolt flange pattern for a direct driveline and axle service replacement.
Key Features
- Part number H513216 for front hub and bearing service
- Fits 1993 Volvo 850, front
- Gen 3 design for application-specific hub bearing replacement
- Pre-greased for ready-to-install service
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 4 bolt holes total
- Inside diameter: 68 mm
- Outside diameter: 135.5 mm
Product Details
Mevotech Supreme hub bearing assemblies are engineered in-house with upgrades tailored to the application. For the Volvo 850 front hub service, H513216 is built for passenger vehicle use and follows the dimensions and mounting layout needed for a proper replacement. The pre-greased construction and Gen 3 design support efficient service on high-use vehicles, including daily-driven cars and working fleets. This part cross-references SKF BR930245 for the same application.
Common Problems This Part Can Address
- Front wheel bearing noise or growling from the hub area
- Excessive wheel play or looseness at the front axle
- ABS-related service needs tied to a non-integral sensor setup
- Hub wear from repeated mileage and load cycles
- Front-end vibration caused by a worn bearing assembly
Installation Notes
Confirm the 4-bolt flange pattern, 68 mm inside diameter, and 135.5 mm outside diameter before installation. This assembly is pre-greased, which helps streamline service, but proper torque procedures and clean mounting surfaces are still important for a secure repair. Verify front-position application on the 1993 Volvo 850 before ordering or installing H513216.
Quality Assurance
Mevotech Supreme parts are engineered in-house with application-specific upgrades for durability and performance. H513216 is built as a service replacement for front hub bearing applications on the 1993 Volvo 850 and is backed by Mevotech’s product engineering standards.
