Mevotech H512412 Wheel Bearing and Hub Assembly - Rear
Mevotech H512412 Rear Hub Assembly
The Mevotech H512412 is a rear wheel bearing and hub assembly engineered for high-use passenger vehicles, SUVs, fleets, and working trucks. Built as a Gen 3 roll-form design and pre-greased for service-ready installation, it is a direct-fit option for select Volvo S40 and Volvo V50 rear applications.
Key Features
- Wheel bearing and hub assembly for rear axle service
- Gen 3 roll-form design for application-specific durability
- Pre-greased for reduced prep time
- Non-integral ABS sensor configuration
- 5 bolt holes with 4 flange bolt holes
- Inside diameter: 63.5 mm
- Outside diameter: 135.8 mm
Detailed Product Overview
Mevotech Supreme Parts are engineered in-house with upgrades tailored to the demands of heavier-use vehicles. The H512412 hub bearing assembly is built for rear service on 2005-2010 Volvo S40 and 2005-2010 Volvo V50 models, making it a focused replacement for drivers searching for a rear wheel bearing and hub assembly for Volvo S40 rear or Volvo V50 rear repair. The H512412 also cross-references Timken HA590321 for the same application.
Common Problems This Part Can Address
- Rear wheel bearing noise or growling from the hub area
- Excessive hub play or looseness at the rear wheel
- ABS-related service needs on a non-integral sensor setup
- Wear-related replacement on high-mileage Volvo S40 and Volvo V50 rear hubs
- Service delays caused by a worn or damaged hub bearing assembly
Installation Notes
Verify rear fitment by year, model, and hub dimensions before installation. Confirm the 5-bolt pattern, 4 flange bolt hole count, and non-integral ABS sensor configuration match the original part. Clean the mounting surface thoroughly and inspect surrounding suspension and brake components during service. The pre-greased design helps streamline installation, but proper torque procedures and vehicle-specific service steps should still be followed.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering for durability and consistent performance in demanding service conditions. This part is designed for direct replacement use on the listed Volvo rear applications and follows Mevotech’s in-house product development standards.
Mevotech H512412 Rear Hub Assembly
The Mevotech H512412 is a rear wheel bearing and hub assembly engineered for high-use passenger vehicles, SUVs, fleets, and working trucks. Built as a Gen 3 roll-form design and pre-greased for service-ready installation, it is a direct-fit option for select Volvo S40 and Volvo V50 rear applications.
Key Features
- Wheel bearing and hub assembly for rear axle service
- Gen 3 roll-form design for application-specific durability
- Pre-greased for reduced prep time
- Non-integral ABS sensor configuration
- 5 bolt holes with 4 flange bolt holes
- Inside diameter: 63.5 mm
- Outside diameter: 135.8 mm
Detailed Product Overview
Mevotech Supreme Parts are engineered in-house with upgrades tailored to the demands of heavier-use vehicles. The H512412 hub bearing assembly is built for rear service on 2005-2010 Volvo S40 and 2005-2010 Volvo V50 models, making it a focused replacement for drivers searching for a rear wheel bearing and hub assembly for Volvo S40 rear or Volvo V50 rear repair. The H512412 also cross-references Timken HA590321 for the same application.
Common Problems This Part Can Address
- Rear wheel bearing noise or growling from the hub area
- Excessive hub play or looseness at the rear wheel
- ABS-related service needs on a non-integral sensor setup
- Wear-related replacement on high-mileage Volvo S40 and Volvo V50 rear hubs
- Service delays caused by a worn or damaged hub bearing assembly
Installation Notes
Verify rear fitment by year, model, and hub dimensions before installation. Confirm the 5-bolt pattern, 4 flange bolt hole count, and non-integral ABS sensor configuration match the original part. Clean the mounting surface thoroughly and inspect surrounding suspension and brake components during service. The pre-greased design helps streamline installation, but proper torque procedures and vehicle-specific service steps should still be followed.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering for durability and consistent performance in demanding service conditions. This part is designed for direct replacement use on the listed Volvo rear applications and follows Mevotech’s in-house product development standards.
Original: $115.80
-65%$115.80
$40.53Description
Mevotech H512412 Rear Hub Assembly
The Mevotech H512412 is a rear wheel bearing and hub assembly engineered for high-use passenger vehicles, SUVs, fleets, and working trucks. Built as a Gen 3 roll-form design and pre-greased for service-ready installation, it is a direct-fit option for select Volvo S40 and Volvo V50 rear applications.
Key Features
- Wheel bearing and hub assembly for rear axle service
- Gen 3 roll-form design for application-specific durability
- Pre-greased for reduced prep time
- Non-integral ABS sensor configuration
- 5 bolt holes with 4 flange bolt holes
- Inside diameter: 63.5 mm
- Outside diameter: 135.8 mm
Detailed Product Overview
Mevotech Supreme Parts are engineered in-house with upgrades tailored to the demands of heavier-use vehicles. The H512412 hub bearing assembly is built for rear service on 2005-2010 Volvo S40 and 2005-2010 Volvo V50 models, making it a focused replacement for drivers searching for a rear wheel bearing and hub assembly for Volvo S40 rear or Volvo V50 rear repair. The H512412 also cross-references Timken HA590321 for the same application.
Common Problems This Part Can Address
- Rear wheel bearing noise or growling from the hub area
- Excessive hub play or looseness at the rear wheel
- ABS-related service needs on a non-integral sensor setup
- Wear-related replacement on high-mileage Volvo S40 and Volvo V50 rear hubs
- Service delays caused by a worn or damaged hub bearing assembly
Installation Notes
Verify rear fitment by year, model, and hub dimensions before installation. Confirm the 5-bolt pattern, 4 flange bolt hole count, and non-integral ABS sensor configuration match the original part. Clean the mounting surface thoroughly and inspect surrounding suspension and brake components during service. The pre-greased design helps streamline installation, but proper torque procedures and vehicle-specific service steps should still be followed.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering for durability and consistent performance in demanding service conditions. This part is designed for direct replacement use on the listed Volvo rear applications and follows Mevotech’s in-house product development standards.
