Mevotech H513162 Wheel Bearing and Hub Assembly - Front
Front Wheel Bearing Hub Assembly for MR2 Spyder
Mevotech H513162 is a front wheel bearing and hub assembly for the 2000-2005 Toyota MR2 Spyder. Built as a pre-greased, Gen 3 roll-form design with a non-integral ABS sensor setup, it is engineered for dependable service on passenger vehicles that see regular road use.
For Toyota MR2 Spyder front hub replacement needs, this Mevotech Supreme assembly combines application-specific design details with a service-friendly layout. The H513162 part number is also referenced in aftermarket cross listings for the same front application.
Key Features
- Fits 2000-2005 Toyota MR2 Spyder, front
- Wheel bearing and hub assembly for driveline and axle service
- Pre-greased for ready-to-install service preparation
- Gen 3 roll-form design for the hub bearing assembly
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 4 bolt holes
- 55 mm inside diameter and 125 mm outside diameter
Product Details
Mevotech Supreme Parts are engineered in-house with application-specific upgrades aimed at durability and performance in high-use passenger vehicles, SUVs, fleets, and working trucks. This front hub assembly for the Toyota MR2 Spyder is built around the correct bearing and hub dimensions, with a pre-greased design that supports efficient service work. If you are replacing a worn front wheel bearing hub assembly on a 2000-2005 Toyota MR2 Spyder, H513162 provides a direct-fit service part for the front position.
This part cross-references Centric Parts 407.44007E for the same application.
Common Problems This Part Can Address
- Front wheel bearing noise or growling
- Excessive hub play or looseness
- Uneven wheel rotation caused by bearing wear
- ABS-related service issues tied to a non-integral sensor setup
- Vibration or roughness from a worn front hub assembly
Installation Notes
Confirm front-position fitment before ordering and verify the hub dimensions, bolt-hole count, and ABS sensor configuration against the original part. Because this assembly is pre-greased, it arrives prepared for installation, but proper torque procedures and vehicle-specific service steps should still be followed during replacement.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering and labor-saving design details to support efficient service and consistent fitment on confirmed applications. H513162 is listed for the 2000-2005 Toyota MR2 Spyder front position.
Front Wheel Bearing Hub Assembly for MR2 Spyder
Mevotech H513162 is a front wheel bearing and hub assembly for the 2000-2005 Toyota MR2 Spyder. Built as a pre-greased, Gen 3 roll-form design with a non-integral ABS sensor setup, it is engineered for dependable service on passenger vehicles that see regular road use.
For Toyota MR2 Spyder front hub replacement needs, this Mevotech Supreme assembly combines application-specific design details with a service-friendly layout. The H513162 part number is also referenced in aftermarket cross listings for the same front application.
Key Features
- Fits 2000-2005 Toyota MR2 Spyder, front
- Wheel bearing and hub assembly for driveline and axle service
- Pre-greased for ready-to-install service preparation
- Gen 3 roll-form design for the hub bearing assembly
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 4 bolt holes
- 55 mm inside diameter and 125 mm outside diameter
Product Details
Mevotech Supreme Parts are engineered in-house with application-specific upgrades aimed at durability and performance in high-use passenger vehicles, SUVs, fleets, and working trucks. This front hub assembly for the Toyota MR2 Spyder is built around the correct bearing and hub dimensions, with a pre-greased design that supports efficient service work. If you are replacing a worn front wheel bearing hub assembly on a 2000-2005 Toyota MR2 Spyder, H513162 provides a direct-fit service part for the front position.
This part cross-references Centric Parts 407.44007E for the same application.
Common Problems This Part Can Address
- Front wheel bearing noise or growling
- Excessive hub play or looseness
- Uneven wheel rotation caused by bearing wear
- ABS-related service issues tied to a non-integral sensor setup
- Vibration or roughness from a worn front hub assembly
Installation Notes
Confirm front-position fitment before ordering and verify the hub dimensions, bolt-hole count, and ABS sensor configuration against the original part. Because this assembly is pre-greased, it arrives prepared for installation, but proper torque procedures and vehicle-specific service steps should still be followed during replacement.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering and labor-saving design details to support efficient service and consistent fitment on confirmed applications. H513162 is listed for the 2000-2005 Toyota MR2 Spyder front position.
Original: $101.79
-65%$101.79
$35.63Description
Front Wheel Bearing Hub Assembly for MR2 Spyder
Mevotech H513162 is a front wheel bearing and hub assembly for the 2000-2005 Toyota MR2 Spyder. Built as a pre-greased, Gen 3 roll-form design with a non-integral ABS sensor setup, it is engineered for dependable service on passenger vehicles that see regular road use.
For Toyota MR2 Spyder front hub replacement needs, this Mevotech Supreme assembly combines application-specific design details with a service-friendly layout. The H513162 part number is also referenced in aftermarket cross listings for the same front application.
Key Features
- Fits 2000-2005 Toyota MR2 Spyder, front
- Wheel bearing and hub assembly for driveline and axle service
- Pre-greased for ready-to-install service preparation
- Gen 3 roll-form design for the hub bearing assembly
- Non-integral ABS sensor configuration
- 4 flange bolt holes and 4 bolt holes
- 55 mm inside diameter and 125 mm outside diameter
Product Details
Mevotech Supreme Parts are engineered in-house with application-specific upgrades aimed at durability and performance in high-use passenger vehicles, SUVs, fleets, and working trucks. This front hub assembly for the Toyota MR2 Spyder is built around the correct bearing and hub dimensions, with a pre-greased design that supports efficient service work. If you are replacing a worn front wheel bearing hub assembly on a 2000-2005 Toyota MR2 Spyder, H513162 provides a direct-fit service part for the front position.
This part cross-references Centric Parts 407.44007E for the same application.
Common Problems This Part Can Address
- Front wheel bearing noise or growling
- Excessive hub play or looseness
- Uneven wheel rotation caused by bearing wear
- ABS-related service issues tied to a non-integral sensor setup
- Vibration or roughness from a worn front hub assembly
Installation Notes
Confirm front-position fitment before ordering and verify the hub dimensions, bolt-hole count, and ABS sensor configuration against the original part. Because this assembly is pre-greased, it arrives prepared for installation, but proper torque procedures and vehicle-specific service steps should still be followed during replacement.
Quality Assurance
Mevotech Supreme hub bearing assemblies are built with application-specific engineering and labor-saving design details to support efficient service and consistent fitment on confirmed applications. H513162 is listed for the 2000-2005 Toyota MR2 Spyder front position.
