Delphi TL2078 Steering Tie Rod End Assembly - Front
Delphi TL2078 Front Steering Tie Rod End Assembly
Restore precise steering response with the Delphi TL2078 steering tie rod end assembly. Built as a standard replacement for the front steering system, it is pre-greased, adjustable, and supplied with a dust boot, washer, mounting hardware, and locking nut for a complete service-ready setup.
Key Features
- Part number: TL2078
- Front steering tie rod end assembly
- Standard replacement design
- Adjustable straight tie rod end
- Pre-greased for initial service
- Dust boot included
- Washer and mounting hardware included
- Aluminum tie rod construction
- Black painted finish
- Clockwise (right) thread direction on both ends
Detailed Description
Delphi applies OE-focused engineering to its aftermarket steering portfolio, and the TL2078 reflects that approach with dimensional and material analysis aimed at proper OE-to-aftermarket match. The assembly uses an aluminum tie rod body with a chloroprene rubber dust boot, a threaded stud design, and a 13.750 in. (349.50 mm) stud-center-to-end length. It is built for front steering service and is listed as a direct replacement style component for Tesla 3 and Tesla Y applications. This part cross-references Mevotech Supreme MS95668 for the same application.
Vehicle Fitment
- Fits 2017-2023 Tesla 3, front
- Fits 2020-2023 Tesla Y, front
Common Problems This Part Can Address
- Loose or vague steering feel
- Excessive play in the front steering linkage
- Uneven tire wear caused by worn tie rod components
- Clunking or knocking from the front suspension and steering area
- Difficulty maintaining proper front-end alignment
Installation Notes and Tips
Confirm thread direction, rod length, and front position before installation. After replacement, perform a professional wheel alignment to set toe and verify steering wheel center. Inspect adjacent steering and suspension components for wear so the new tie rod end is not installed into a worn system.
Quality Assurance
Delphi subjects steering components to extreme temperature and corrosion testing, including exposure below -40 degrees C, above 120 degrees C, and extended salt-spray testing. The TL2078 is backed by Delphi OE-focused manufacturing standards for consistent fit and performance.
Delphi TL2078 Front Steering Tie Rod End Assembly
Restore precise steering response with the Delphi TL2078 steering tie rod end assembly. Built as a standard replacement for the front steering system, it is pre-greased, adjustable, and supplied with a dust boot, washer, mounting hardware, and locking nut for a complete service-ready setup.
Key Features
- Part number: TL2078
- Front steering tie rod end assembly
- Standard replacement design
- Adjustable straight tie rod end
- Pre-greased for initial service
- Dust boot included
- Washer and mounting hardware included
- Aluminum tie rod construction
- Black painted finish
- Clockwise (right) thread direction on both ends
Detailed Description
Delphi applies OE-focused engineering to its aftermarket steering portfolio, and the TL2078 reflects that approach with dimensional and material analysis aimed at proper OE-to-aftermarket match. The assembly uses an aluminum tie rod body with a chloroprene rubber dust boot, a threaded stud design, and a 13.750 in. (349.50 mm) stud-center-to-end length. It is built for front steering service and is listed as a direct replacement style component for Tesla 3 and Tesla Y applications. This part cross-references Mevotech Supreme MS95668 for the same application.
Vehicle Fitment
- Fits 2017-2023 Tesla 3, front
- Fits 2020-2023 Tesla Y, front
Common Problems This Part Can Address
- Loose or vague steering feel
- Excessive play in the front steering linkage
- Uneven tire wear caused by worn tie rod components
- Clunking or knocking from the front suspension and steering area
- Difficulty maintaining proper front-end alignment
Installation Notes and Tips
Confirm thread direction, rod length, and front position before installation. After replacement, perform a professional wheel alignment to set toe and verify steering wheel center. Inspect adjacent steering and suspension components for wear so the new tie rod end is not installed into a worn system.
Quality Assurance
Delphi subjects steering components to extreme temperature and corrosion testing, including exposure below -40 degrees C, above 120 degrees C, and extended salt-spray testing. The TL2078 is backed by Delphi OE-focused manufacturing standards for consistent fit and performance.
Description
Delphi TL2078 Front Steering Tie Rod End Assembly
Restore precise steering response with the Delphi TL2078 steering tie rod end assembly. Built as a standard replacement for the front steering system, it is pre-greased, adjustable, and supplied with a dust boot, washer, mounting hardware, and locking nut for a complete service-ready setup.
Key Features
- Part number: TL2078
- Front steering tie rod end assembly
- Standard replacement design
- Adjustable straight tie rod end
- Pre-greased for initial service
- Dust boot included
- Washer and mounting hardware included
- Aluminum tie rod construction
- Black painted finish
- Clockwise (right) thread direction on both ends
Detailed Description
Delphi applies OE-focused engineering to its aftermarket steering portfolio, and the TL2078 reflects that approach with dimensional and material analysis aimed at proper OE-to-aftermarket match. The assembly uses an aluminum tie rod body with a chloroprene rubber dust boot, a threaded stud design, and a 13.750 in. (349.50 mm) stud-center-to-end length. It is built for front steering service and is listed as a direct replacement style component for Tesla 3 and Tesla Y applications. This part cross-references Mevotech Supreme MS95668 for the same application.
Vehicle Fitment
- Fits 2017-2023 Tesla 3, front
- Fits 2020-2023 Tesla Y, front
Common Problems This Part Can Address
- Loose or vague steering feel
- Excessive play in the front steering linkage
- Uneven tire wear caused by worn tie rod components
- Clunking or knocking from the front suspension and steering area
- Difficulty maintaining proper front-end alignment
Installation Notes and Tips
Confirm thread direction, rod length, and front position before installation. After replacement, perform a professional wheel alignment to set toe and verify steering wheel center. Inspect adjacent steering and suspension components for wear so the new tie rod end is not installed into a worn system.
Quality Assurance
Delphi subjects steering components to extreme temperature and corrosion testing, including exposure below -40 degrees C, above 120 degrees C, and extended salt-spray testing. The TL2078 is backed by Delphi OE-focused manufacturing standards for consistent fit and performance.
