Delphi TD1636W Suspension Control Arm Bushing - Front Upper
Delphi TD1636W Front Upper Bushing
Delphi TD1636W is a suspension control arm bushing for the front upper position, built as a standard replacement for select Audi applications. It uses aluminum bushing material with a 70 ShA durometer rating and precise OE-focused dimensions for consistent suspension fitment.
Key Features
- Suspension control arm bushing for front upper placement
- Aluminum bushing material with gray finish
- 70 ShA hardness for controlled suspension response
- Standard replacement grade
- Single bushing quantity
- No grease fitting, dust boot, sleeve, bracket, or mounting hardware included
Product Details
Delphi applies OE engineering and dimensional analysis to its aftermarket steering and suspension portfolio, and the TD1636W reflects that approach with carefully measured dimensions: 1.810 in. length and width, 1.570 in. height, and a 0.400 in. inside diameter. The bushing is specified for manual steering systems and is listed as non-greaseable and non-reinforced. This part cross-references Beck/Arnley 101-8155 for the same application. Fits 2012-2018 Audi A6, Front Upper. Fits 2012-2018 Audi A6 Quattro, Front Upper. Fits 2012-2018 Audi A7 Quattro, Front Upper. Fits 2014-2018 Audi RS7, Front Upper. Fits 2013-2018 Audi S6, Front Upper. Fits 2013-2018 Audi S7, Front Upper. Fits 2011-2014 Audi A8 Quattro, Front Upper. Fits 2013-2014 Audi S8, Front Upper. Delphi TD1636W is also referenced for OE numbers 4H0 407 515, 4H0 407 515 A, and 4H0 407 515 B.
Common Repair Uses
- Replacing worn front upper control arm bushings
- Addressing looseness or play in the front suspension
- Restoring consistent alignment retention after bushing wear
- Reducing clunking or shifting from deteriorated suspension bushings
- Servicing front suspension on Audi A6, A7, S6, S7, RS7, A8 Quattro, and S8 models
Installation Notes
Verify the front upper position and confirm the OE reference before installation. Because this is a bushing-only part, reuse or separately source any required control arm components not included with the bushing. Inspect the control arm for wear, corrosion, or deformation before pressing in the new bushing, and follow factory service procedures for alignment after installation.
Quality Assurance
Delphi tests suspension and steering components across extreme temperature ranges below -40 degrees C and above 120 degrees C, and exposes parts to 720 hours of salt spray during validation. That OE-focused testing, along with dimensional and material analysis, supports consistent fit and performance for the listed Audi applications.
Delphi TD1636W Front Upper Bushing
Delphi TD1636W is a suspension control arm bushing for the front upper position, built as a standard replacement for select Audi applications. It uses aluminum bushing material with a 70 ShA durometer rating and precise OE-focused dimensions for consistent suspension fitment.
Key Features
- Suspension control arm bushing for front upper placement
- Aluminum bushing material with gray finish
- 70 ShA hardness for controlled suspension response
- Standard replacement grade
- Single bushing quantity
- No grease fitting, dust boot, sleeve, bracket, or mounting hardware included
Product Details
Delphi applies OE engineering and dimensional analysis to its aftermarket steering and suspension portfolio, and the TD1636W reflects that approach with carefully measured dimensions: 1.810 in. length and width, 1.570 in. height, and a 0.400 in. inside diameter. The bushing is specified for manual steering systems and is listed as non-greaseable and non-reinforced. This part cross-references Beck/Arnley 101-8155 for the same application. Fits 2012-2018 Audi A6, Front Upper. Fits 2012-2018 Audi A6 Quattro, Front Upper. Fits 2012-2018 Audi A7 Quattro, Front Upper. Fits 2014-2018 Audi RS7, Front Upper. Fits 2013-2018 Audi S6, Front Upper. Fits 2013-2018 Audi S7, Front Upper. Fits 2011-2014 Audi A8 Quattro, Front Upper. Fits 2013-2014 Audi S8, Front Upper. Delphi TD1636W is also referenced for OE numbers 4H0 407 515, 4H0 407 515 A, and 4H0 407 515 B.
Common Repair Uses
- Replacing worn front upper control arm bushings
- Addressing looseness or play in the front suspension
- Restoring consistent alignment retention after bushing wear
- Reducing clunking or shifting from deteriorated suspension bushings
- Servicing front suspension on Audi A6, A7, S6, S7, RS7, A8 Quattro, and S8 models
Installation Notes
Verify the front upper position and confirm the OE reference before installation. Because this is a bushing-only part, reuse or separately source any required control arm components not included with the bushing. Inspect the control arm for wear, corrosion, or deformation before pressing in the new bushing, and follow factory service procedures for alignment after installation.
Quality Assurance
Delphi tests suspension and steering components across extreme temperature ranges below -40 degrees C and above 120 degrees C, and exposes parts to 720 hours of salt spray during validation. That OE-focused testing, along with dimensional and material analysis, supports consistent fit and performance for the listed Audi applications.
Description
Delphi TD1636W Front Upper Bushing
Delphi TD1636W is a suspension control arm bushing for the front upper position, built as a standard replacement for select Audi applications. It uses aluminum bushing material with a 70 ShA durometer rating and precise OE-focused dimensions for consistent suspension fitment.
Key Features
- Suspension control arm bushing for front upper placement
- Aluminum bushing material with gray finish
- 70 ShA hardness for controlled suspension response
- Standard replacement grade
- Single bushing quantity
- No grease fitting, dust boot, sleeve, bracket, or mounting hardware included
Product Details
Delphi applies OE engineering and dimensional analysis to its aftermarket steering and suspension portfolio, and the TD1636W reflects that approach with carefully measured dimensions: 1.810 in. length and width, 1.570 in. height, and a 0.400 in. inside diameter. The bushing is specified for manual steering systems and is listed as non-greaseable and non-reinforced. This part cross-references Beck/Arnley 101-8155 for the same application. Fits 2012-2018 Audi A6, Front Upper. Fits 2012-2018 Audi A6 Quattro, Front Upper. Fits 2012-2018 Audi A7 Quattro, Front Upper. Fits 2014-2018 Audi RS7, Front Upper. Fits 2013-2018 Audi S6, Front Upper. Fits 2013-2018 Audi S7, Front Upper. Fits 2011-2014 Audi A8 Quattro, Front Upper. Fits 2013-2014 Audi S8, Front Upper. Delphi TD1636W is also referenced for OE numbers 4H0 407 515, 4H0 407 515 A, and 4H0 407 515 B.
Common Repair Uses
- Replacing worn front upper control arm bushings
- Addressing looseness or play in the front suspension
- Restoring consistent alignment retention after bushing wear
- Reducing clunking or shifting from deteriorated suspension bushings
- Servicing front suspension on Audi A6, A7, S6, S7, RS7, A8 Quattro, and S8 models
Installation Notes
Verify the front upper position and confirm the OE reference before installation. Because this is a bushing-only part, reuse or separately source any required control arm components not included with the bushing. Inspect the control arm for wear, corrosion, or deformation before pressing in the new bushing, and follow factory service procedures for alignment after installation.
Quality Assurance
Delphi tests suspension and steering components across extreme temperature ranges below -40 degrees C and above 120 degrees C, and exposes parts to 720 hours of salt spray during validation. That OE-focused testing, along with dimensional and material analysis, supports consistent fit and performance for the listed Audi applications.
