Delphi TC7041 Lateral Arm - Rear Left Upper
Delphi TC7041 Rear Left Upper Lateral Arm
Delphi TC7041 is a rear left upper lateral arm for select Subaru Legacy and Subaru Outback applications. Built with a cast construction and rubber bushings, it is engineered for direct replacement service where rear suspension geometry and bushing condition matter.
Key Features
- Part number: TC7041
- Position: Rear left upper
- Cast arm construction
- Black finish with black bushings
- Rubber bushings included
- Pre-greased: No
- Grease fittings included: No
- Mounting hardware included: No
- Length: 13.5 in. (343.8 mm)
Detailed Description
This Delphi lateral arm is built for rear suspension service on 2000-2009 Subaru Legacy and 2008-2009 Subaru Outback models in the rear left upper position. Delphi applies OE-focused dimensional and material analysis to help ensure proper part-to-vehicle match, and the component is tested for temperature extremes and salt spray exposure to support durability in demanding conditions. If you are replacing a worn rear suspension arm on a Subaru Legacy or Subaru Outback, TC7041 provides a direct-fit service part for the specified application.
This part cross-references Dorman OE Solutions 524-189 for the same application.
What It Helps Address
- Rear suspension looseness or instability from a worn lateral arm
- Clunking or knocking noises from deteriorated bushings
- Uneven rear wheel alignment caused by suspension wear
- Excess movement in the rear left upper suspension link
- Restoration of proper rear suspension geometry on Subaru Legacy and Subaru Outback models
Installation Notes and Tips
- Verify vehicle year, make, model, and rear left upper position before ordering.
- Inspect adjacent suspension bushings and mounting points during replacement.
- Mounting hardware is not included, so reuse or replace fasteners as needed based on condition.
- Because this arm is not pre-greased and has no grease fittings, confirm the bushing condition before installation.
Quality Assurance
Delphi uses OE-based engineering practices and extensive dimensional and material analysis to support fitment accuracy. The part is also subjected to temperature testing below -40 degrees C and above 120 degrees C, along with 720 hours of salt spray exposure, to evaluate performance under harsh operating conditions.
- Fits 2000-2009 Subaru Legacy, rear left upper
- Fits 2008-2009 Subaru Outback, rear left upper
Delphi TC7041 Rear Left Upper Lateral Arm
Delphi TC7041 is a rear left upper lateral arm for select Subaru Legacy and Subaru Outback applications. Built with a cast construction and rubber bushings, it is engineered for direct replacement service where rear suspension geometry and bushing condition matter.
Key Features
- Part number: TC7041
- Position: Rear left upper
- Cast arm construction
- Black finish with black bushings
- Rubber bushings included
- Pre-greased: No
- Grease fittings included: No
- Mounting hardware included: No
- Length: 13.5 in. (343.8 mm)
Detailed Description
This Delphi lateral arm is built for rear suspension service on 2000-2009 Subaru Legacy and 2008-2009 Subaru Outback models in the rear left upper position. Delphi applies OE-focused dimensional and material analysis to help ensure proper part-to-vehicle match, and the component is tested for temperature extremes and salt spray exposure to support durability in demanding conditions. If you are replacing a worn rear suspension arm on a Subaru Legacy or Subaru Outback, TC7041 provides a direct-fit service part for the specified application.
This part cross-references Dorman OE Solutions 524-189 for the same application.
What It Helps Address
- Rear suspension looseness or instability from a worn lateral arm
- Clunking or knocking noises from deteriorated bushings
- Uneven rear wheel alignment caused by suspension wear
- Excess movement in the rear left upper suspension link
- Restoration of proper rear suspension geometry on Subaru Legacy and Subaru Outback models
Installation Notes and Tips
- Verify vehicle year, make, model, and rear left upper position before ordering.
- Inspect adjacent suspension bushings and mounting points during replacement.
- Mounting hardware is not included, so reuse or replace fasteners as needed based on condition.
- Because this arm is not pre-greased and has no grease fittings, confirm the bushing condition before installation.
Quality Assurance
Delphi uses OE-based engineering practices and extensive dimensional and material analysis to support fitment accuracy. The part is also subjected to temperature testing below -40 degrees C and above 120 degrees C, along with 720 hours of salt spray exposure, to evaluate performance under harsh operating conditions.
- Fits 2000-2009 Subaru Legacy, rear left upper
- Fits 2008-2009 Subaru Outback, rear left upper
Original: $99.38
-65%$99.38
$34.78Description
Delphi TC7041 Rear Left Upper Lateral Arm
Delphi TC7041 is a rear left upper lateral arm for select Subaru Legacy and Subaru Outback applications. Built with a cast construction and rubber bushings, it is engineered for direct replacement service where rear suspension geometry and bushing condition matter.
Key Features
- Part number: TC7041
- Position: Rear left upper
- Cast arm construction
- Black finish with black bushings
- Rubber bushings included
- Pre-greased: No
- Grease fittings included: No
- Mounting hardware included: No
- Length: 13.5 in. (343.8 mm)
Detailed Description
This Delphi lateral arm is built for rear suspension service on 2000-2009 Subaru Legacy and 2008-2009 Subaru Outback models in the rear left upper position. Delphi applies OE-focused dimensional and material analysis to help ensure proper part-to-vehicle match, and the component is tested for temperature extremes and salt spray exposure to support durability in demanding conditions. If you are replacing a worn rear suspension arm on a Subaru Legacy or Subaru Outback, TC7041 provides a direct-fit service part for the specified application.
This part cross-references Dorman OE Solutions 524-189 for the same application.
What It Helps Address
- Rear suspension looseness or instability from a worn lateral arm
- Clunking or knocking noises from deteriorated bushings
- Uneven rear wheel alignment caused by suspension wear
- Excess movement in the rear left upper suspension link
- Restoration of proper rear suspension geometry on Subaru Legacy and Subaru Outback models
Installation Notes and Tips
- Verify vehicle year, make, model, and rear left upper position before ordering.
- Inspect adjacent suspension bushings and mounting points during replacement.
- Mounting hardware is not included, so reuse or replace fasteners as needed based on condition.
- Because this arm is not pre-greased and has no grease fittings, confirm the bushing condition before installation.
Quality Assurance
Delphi uses OE-based engineering practices and extensive dimensional and material analysis to support fitment accuracy. The part is also subjected to temperature testing below -40 degrees C and above 120 degrees C, along with 720 hours of salt spray exposure, to evaluate performance under harsh operating conditions.
- Fits 2000-2009 Subaru Legacy, rear left upper
- Fits 2008-2009 Subaru Outback, rear left upper
