Delphi TA3381 Steering Tie Rod End - Front Right Outer
OE-Style Steering Tie Rod End for Honda HR-V
Delphi TA3381 is a front right outer steering tie rod end built for precise steering response and dependable replacement performance. It is listed for 2016-2021 Honda HR-V applications and follows OE-style dimensions for a direct-service fit on the front right outer position.
Delphi applies OE engineering to its aftermarket steering parts, with dimensional and material analysis used to support fit and compatibility. This Delphi TA3381 tie rod end is pre-greased, includes a dust boot, and uses a steel housing and steel tie rod construction for standard replacement service.
Key Features
- Fits 2016-2021 Honda HR-V, front right outer
- Delphi TA3381 steering tie rod end
- Pre-greased for service-ready installation
- Dust boot included to help protect the joint
- Steel housing and steel tie rod material
- Bent design with threaded stud construction
- Standard replacement grade for OE-style service
- Mounting hardware included
Detailed Description
Use Delphi TA3381 when replacing a worn front right outer tie rod end on a Honda HR-V. The part is engineered with a female end 1 and male end 2 configuration, clockwise thread direction on both ends, and a 15.10 mm shank/stud diameter. Its bent profile, rubber dust boot, and pre-greased design support straightforward steering linkage service while maintaining the original steering geometry expected in OE replacement work. Delphi TA3381 also cross-references MOOG Chassis Products ES801388 for the same application.
Common Problems This Part Can Help Address
- Loose or vague steering feel at the front right wheel
- Uneven tire wear caused by worn steering linkage components
- Clunking or play in the outer tie rod end
- Steering pull or reduced directional stability
- Failed inspection due to excessive steering joint wear
Installation Notes and Tips
Install Delphi TA3381 on the front right outer steering position only. After replacement, have the vehicle inspected for proper toe alignment, since tie rod service can change steering geometry. Verify thread direction, stud dimensions, and overall length against the removed part before installation on your Honda HR-V.
Quality Assurance
Delphi subjects its steering components to OE-level validation, including extreme temperature exposure below -40 degrees C and above 120 degrees C, plus extended salt-spray testing. The brand also uses dimensional and material analysis to support OE-to-aftermarket fit consistency for Honda HR-V steering service.
OE-Style Steering Tie Rod End for Honda HR-V
Delphi TA3381 is a front right outer steering tie rod end built for precise steering response and dependable replacement performance. It is listed for 2016-2021 Honda HR-V applications and follows OE-style dimensions for a direct-service fit on the front right outer position.
Delphi applies OE engineering to its aftermarket steering parts, with dimensional and material analysis used to support fit and compatibility. This Delphi TA3381 tie rod end is pre-greased, includes a dust boot, and uses a steel housing and steel tie rod construction for standard replacement service.
Key Features
- Fits 2016-2021 Honda HR-V, front right outer
- Delphi TA3381 steering tie rod end
- Pre-greased for service-ready installation
- Dust boot included to help protect the joint
- Steel housing and steel tie rod material
- Bent design with threaded stud construction
- Standard replacement grade for OE-style service
- Mounting hardware included
Detailed Description
Use Delphi TA3381 when replacing a worn front right outer tie rod end on a Honda HR-V. The part is engineered with a female end 1 and male end 2 configuration, clockwise thread direction on both ends, and a 15.10 mm shank/stud diameter. Its bent profile, rubber dust boot, and pre-greased design support straightforward steering linkage service while maintaining the original steering geometry expected in OE replacement work. Delphi TA3381 also cross-references MOOG Chassis Products ES801388 for the same application.
Common Problems This Part Can Help Address
- Loose or vague steering feel at the front right wheel
- Uneven tire wear caused by worn steering linkage components
- Clunking or play in the outer tie rod end
- Steering pull or reduced directional stability
- Failed inspection due to excessive steering joint wear
Installation Notes and Tips
Install Delphi TA3381 on the front right outer steering position only. After replacement, have the vehicle inspected for proper toe alignment, since tie rod service can change steering geometry. Verify thread direction, stud dimensions, and overall length against the removed part before installation on your Honda HR-V.
Quality Assurance
Delphi subjects its steering components to OE-level validation, including extreme temperature exposure below -40 degrees C and above 120 degrees C, plus extended salt-spray testing. The brand also uses dimensional and material analysis to support OE-to-aftermarket fit consistency for Honda HR-V steering service.
Original: $29.44
-65%$29.44
$10.30Description
OE-Style Steering Tie Rod End for Honda HR-V
Delphi TA3381 is a front right outer steering tie rod end built for precise steering response and dependable replacement performance. It is listed for 2016-2021 Honda HR-V applications and follows OE-style dimensions for a direct-service fit on the front right outer position.
Delphi applies OE engineering to its aftermarket steering parts, with dimensional and material analysis used to support fit and compatibility. This Delphi TA3381 tie rod end is pre-greased, includes a dust boot, and uses a steel housing and steel tie rod construction for standard replacement service.
Key Features
- Fits 2016-2021 Honda HR-V, front right outer
- Delphi TA3381 steering tie rod end
- Pre-greased for service-ready installation
- Dust boot included to help protect the joint
- Steel housing and steel tie rod material
- Bent design with threaded stud construction
- Standard replacement grade for OE-style service
- Mounting hardware included
Detailed Description
Use Delphi TA3381 when replacing a worn front right outer tie rod end on a Honda HR-V. The part is engineered with a female end 1 and male end 2 configuration, clockwise thread direction on both ends, and a 15.10 mm shank/stud diameter. Its bent profile, rubber dust boot, and pre-greased design support straightforward steering linkage service while maintaining the original steering geometry expected in OE replacement work. Delphi TA3381 also cross-references MOOG Chassis Products ES801388 for the same application.
Common Problems This Part Can Help Address
- Loose or vague steering feel at the front right wheel
- Uneven tire wear caused by worn steering linkage components
- Clunking or play in the outer tie rod end
- Steering pull or reduced directional stability
- Failed inspection due to excessive steering joint wear
Installation Notes and Tips
Install Delphi TA3381 on the front right outer steering position only. After replacement, have the vehicle inspected for proper toe alignment, since tie rod service can change steering geometry. Verify thread direction, stud dimensions, and overall length against the removed part before installation on your Honda HR-V.
Quality Assurance
Delphi subjects its steering components to OE-level validation, including extreme temperature exposure below -40 degrees C and above 120 degrees C, plus extended salt-spray testing. The brand also uses dimensional and material analysis to support OE-to-aftermarket fit consistency for Honda HR-V steering service.
